Sumachay SS60 walk-behind floor scrubber, front three-quarter view

Sumachay SS60 walk-behind floor scrubber front view with scrub brush

Sumachay SS60 floor scrubber operator view showing control head and squeegee

Sumachay SS60 floor scrubber rear view with squeegee and handle

Sumachay SS60 floor scrubber control panel with key switch and battery gauge

Sumachay SS60 floor scrubber scrub brush and cleaning deck

Sumachay SS60 floor scrubber rear squeegee assembly with casters

Sumachay SS60 floor scrubber battery and vacuum motor compartment

Sumachay SS60 floor scrubber included accessories, tools and manual

Sumachay SS60 floor scrubber battery charger included

Sumachay SS60 floor scrubber CSA certification and specification plate

INDUSTRIAL CLEANING SERIESWalk-Behind Scrubber

Walk-Behind Floor Scrubber | Sumachay SS60 | 21 Inch Cleaning Path

Q: Sweeper or scrubber: which one do I need?

Sweepers (like the SL1250 ride-on sweeper ) collect dry debris : dust, dirt, leaves, packaging. They use brushes and a dustbin. Scrubbers (like the SS60) apply a cleaning solution through brushes and recover the dirty water through a squeegee, leaving floors visibly clean and dry. Many large facilities run both. If your floors collect dry debris, you need a sweeper. If your floors are sealed and need to look clean and disinfected, and the mop bucket is the bottleneck, you need a scrubber.

Q: How long does the SS60 run on a single charge?

3 to 5 hours of continuous scrubbing per full charge, depending on solution flow rate and floor conditions. The lithium-ion battery supports opportunity charging during operator breaks, which extends total shift coverage. Full charge from empty takes 3 to 4 hours .

Q: Can the SS60 be used outdoors or on asphalt?

No. The SS60 is engineered for indoor sealed hard floors only : sealed concrete, epoxy, polished concrete, and ceramic or porcelain tile. It is not suitable for asphalt, gravel, raw or unsealed concrete, or any outdoor surface, and is not designed for floors exposed to rain, snow, or freezing temperatures.

Q: What maintenance does the SS60 need?

After every shift: drain and rinse the recovery (dirty-water) tank, rinse the squeegee, and inspect the brushes. Monthly: clean the solution-tank filter, check the squeegee blades for wear and rotate them, and clean the seals on the recovery tank lid. As needed: replace brushes (typically every 6 to 12 months depending on use) and squeegee blades (consumable). Lithium-ion batteries are maintenance-free for the warranty period: no watering, no equalization, no off-gassing.

Q: What cleaning solution should I use in the SS60?

Use a low-foam, pH-neutral commercial floor detergent , diluted to the ratio on the container, with water up to 60 °C. A neutral cleaner suits daily cleaning on sealed concrete, epoxy, polished concrete and tile; a low-foam alkaline degreaser handles grease in food-service or workshop areas (test a small area first). Never use high-foam or dish soaps, bleach, strong acids, solvents, flammable liquids, or powder detergent — they damage the machine and void the warranty. If foam builds up, add defoamer to the recovery tank, not the solution tank. See the “What to put in the solution tank” section above for the full guide.

Q: How do I request a delivery quote for the SS60?

Use the "Request a Delivery Quote" button on this page or contact us at sales@sumachay.com or 1-844-861-9484. The SS60 ships on a pallet via LTL freight or smaller-format courier depending on facility access. Delivery typically takes 5 to 10 business days after 1 to 3 days of handling. Liftgate delivery and appointment scheduling are available on most routes.

Q: What warranty comes with the SS60?

The SS60 includes a 12-month equipment warranty covering the brush motor, suction motor, controller, control panel, and lithium battery against manufacturing defects under normal operating conditions. Wear items (squeegee blades, scrub brushes, scrub pads, rubber strips, brush plates) are excluded. Warranty registration is automatic at purchase.

21″ walk-behind scrubber • ~28,000 sq ft/hr for sealed indoor floors in warehouses, hospitals, retail, and offices.

$4,000.00 CAD

In Stock in Canada

Direct from Manufacturer

12-Month Warranty

Financing Available

Canadian Support

At a Glance

21.3″ Scrubbing Path (540 mm)

2600 m²/hr (28000 ft²/hr)

24V / 100Ah Lithium Battery

3.0–4.0 hr Runtime per Charge

55.0 L Solution Tank60.0 L Recovery Tank

Walk-behind 21-inch (540 mm) scrubber for facilities cleaning up to ~28,000 sq ft per hour. One operator, one charge, sealed floors fully scrubbed and dried. Built for mid-sized warehouses, hospitals, retail, and office buildings cleaning under ~30,000 sq ft per shift. Indoor sealed floors only: sealed concrete, epoxy, polished concrete, ceramic and porcelain tile. Supported by Sumachay in Canada.

Have questions? See FAQ ↓Browse all floor cleaners

Available across Canada. Ships from our Toronto distribution centre (840 Flint Road, North York, ON).

Estimate shipping

Shipping & pickup

Ships as 1 pallet (skid)

Package size 53.94 × 24.8 × 46.06 in

Weight ~319.7 lb

In stock
Ships across Canada (LTL freight)
1–3 Business Day Dispatch
1-Year Warranty
Phone support

Need help choosing? Talk to a product specialist →

Prefer a quote first?

Trusted by Leading Canadian Operations Teams

★★★★★ 5.0 Excellent 335 Google Reviews Read reviews →

Customer proof

Trusted by Canadian Warehouses

5.0335+ Google reviews

Google Review

Sturdy, easy to use, and perfect for handling heavy loads. The customer service really stood out, and everything arrived in perfect condition. Highly recommend Sumachay.
Sachin L.Sumachay Pallet Jack
Google Review

Bought an electric pallet jack from Sumachay. Great product with a great price, and the best, friendliest customer service. Definitely recommended.
Sathiya M.Electric Pallet Jack
Google Review

Bought a manual pallet jack first, then came back for the SELR20 Electric Pallet Jack. They even helped me fit it into my car.
KLMSELR20 Electric Pallet Jack
Google Review

Purchased electric and manual pallet jacks and loaded them in my van. Great price and great customer service. Definitely recommended.
Harpreet S.Electric & Manual Pallet Jack
Google Review

Great product and great service. The pallet jack is best quality.
Aleem H.Sumachay Pallet Jack
Google Review

Great service, and a great choice with the pallet stacker and the hand pump truck. Both are electric and work amazingly well.
Kirk R.Electric Stacker & Pump Truck
Google Review

Best quality packaging products and prices in the GTA for all our warehouse supplies.
Himanshu T.Warehouse Supplies
Google Review

Great experience buying stretch wrap and an electric pallet jack. Quality and service were excellent.
Damien G.Stretch Wrap & Electric Pallet Jack

Great product with a great price, and the best, friendliest customer service. Definitely recommended.

Sathiya M.

Verified buyer

Ships crated on a single pallet via LTL freight from our Toronto warehouse.

Freight is calculated by weight and delivery location — most Canadian deliveries range $180–$500 depending on province and urban vs. rural access. Liftgate delivery and appointment scheduling available; typical transit 5–10 business days after 1–3 days handling.

See the SS60 in Action

Is this the right floor cleaner for your facility?

Choose this machine when

You scrub sealed floors (concrete, epoxy, tile, vinyl) where solution and recovery are both required.
Your facility size and frequency of cleaning justify a self-propelled machine over manual mopping.
You need consistent scrub pressure for grease, soil, or food-service residue removal.
You want squeegee-and-vacuum recovery so floors are dry and walkable immediately after cleaning.

Consider an alternative if

You only need dry sweeping for loose debris. See SL1250 ride-on sweeper →
Your floor is unsealed (raw concrete, gravel, dirt). Scrubbing solution will not be effective.
Your facility is over 30,000 sq ft per shift, or you run multiple cleaning shifts daily. Step up to SS75-R ride-on →

Fit & Compatibility

Will it fit your facility?

Compact 21-inch walk-behind footprint. Sealed indoor floors only. Verify your aisle widths and surface type before ordering.

Footprint & Clearance

Overall length 47.2 in 1,200 mm

Overall width 30.7 in 780 mm

Overall height 37.8 in 960 mm

Cleaning path 21 in 540 mm

Squeegee width 31.5 in 800 mm

Service weight 320 lb 145 kg

Ramp capability

Loaded

Max safe incline

Unloaded

Max safe incline

Surface compatibility

Sealed concrete (warehouse / factory floor)
Epoxy coating
Polished concrete
Ceramic and porcelain tile

Compare the lineup

Compare scrubber models and find your fit

The SS60 walk-behind suits mid-sized, tighter, obstacle-heavy floors. Step up to the SS75-R ride-on for large open floors over ~30,000 sq ft per shift.

Quick selection guide

Current Model

SS60

Walk-behind scrubber for mid-sized floors

21 in (540 mm) scrub path
55 L solution + 60 L recovery
24V 100Ah · 3–4 hr runtime
~28,000 sq ft/hr

Designed For 5,000–30,000 sq ft per shift; tight aisles and obstacle-heavy floors; operator on foot.

Not Recommended Open floors over ~30,000 sq ft per shift — step up to the SS75-R ride-on.

View model details

Step up · Ride-on

SS75-R

Ride-on scrubber for large facilities

26 in (660 mm) scrub path
75 L solution + 95 L recovery
24V 80Ah lithium · 3–4 hr runtime
~37,600 sq ft/hr

Designed For 30,000+ sq ft per shift; open floor plans; long shifts (ride-on removes operator fatigue).

Not Recommended Tight aisles or obstacle-heavy floors — use the SS60 walk-behind.

View model details

Why It's Different

~17× faster than mop and bucket.

A single operator with mop and bucket caps out around 1,500 sq ft per hour and leaves wet floors that can stay slick for 20 minutes. The SS60 covers ~25,300 sq ft per hour and leaves the floor squeegee-dry behind it.

Feature SS60 Walk-Behind Scrubber Manual mop and bucket

Cleaning throughput ~25,300 sq ft/hr ~1,500 sq ft/hr

Labour required 1 walking operator 1 operator on foot

Water hygiene Separate fresh and recovery tanks Cross-contamination from one bucket

Floor dryness after pass Squeegee-dry; walkable in seconds ~20 min slip-risk window

Runtime per shift 3 to 5 hr lithium Operator-limited

Consistency of cleaning Calibrated brush pressure and metered solution Variable, operator-dependent

Recovery 18.5 US gal recovery tank Bucket cycles

Technical Specifications

Complete engineering data.

Cleaning system

Cleaning path 21.3 in (540 mm)

Productivity 2600 m²/hr (27986 ft²/hr)

Solution tank 55.0 L

Recovery tank 60.0 L

Squeegee width 31.5 in (800 mm)

Brush set 2 scrub brushes, 540 mm cleaning path

Dimensions

Overall L x W x H 1200 × 780 × 960 mm (L × W × H)

Service weight 320 lb (145 kg)

Power system

Voltage / capacity 24V / 100Ah

Battery type Lithium-ion maintenance-free

Runtime per charge 3.0–4.0 hrs

Full charge time 3 to 4 hr

Motor configuration Brush 550 W + Suction 500 W (24 V)

Performance

Operator pace (recommended) 150 to 200 ft/min (45 to 60 m/min)

Max gradeability 5%

Compliance

Warranty 12 months (equipment)

What's in the box

Everything required to start cleaning on day one.

SS60 walk-behind floor scrubber, fully assembled
24V 100Ah lithium-ion battery, installed
24V 15A automatic charger
Squeegee assembly with rubber strips
2 floor scrub brushes
3 operator key cards
User manual, warranty card, certificate of conformity

Final included accessories may vary by configuration. Confirm with your sales rep on the RFQ.

Solution tank & cleaning products

What to put in the solution tank

The 55.0 L solution tank holds the formula the brushes apply. Fill it with water — hot water up to 60 °C is fine — plus a low-foam, pH-neutral commercial floor detergent, diluted to the ratio printed on the product label. The right choice depends on your floor type and soil level.

Daily neutral-pH cleaner

For everyday cleaning of sealed concrete, epoxy, polished concrete and tile. Low-foam, residue-free and safe for polished or coated finishes. Use the label's daily-clean dilution.

Low-foam alkaline degreaser

For grease and oil in food service, workshops and garages. Dilute stronger for heavy soil and test a small area first — not for polished or waxed finishes.

Autoscrubber-safe neutral disinfectant

For healthcare and food-prep areas, only if the label says low-foam and autoscrubber-compatible. Observe the product's required dwell time.

Plain hot water (≤ 60 °C)

For light maintenance and rinse passes. For stubborn dirt or grease, add a recommended commercial detergent rather than more foam.

Use a low-foam, pH-neutral commercial floor detergent
Follow the dilution ratio on the container
Fill with water, up to 60 °C maximum
Test a small area before treating the whole floor
If foam builds up, add defoamer to the recovery tank

Don't

High-foam, dish or household soaps — they flood the suction motor
Bleach and chlorine products — corrosive to components
Strong acids or acidic descalers
Caustic, solvent or thinner-based products
Flammable liquids
Granular or powder detergent (e.g. washing powder) — voids the warranty
Never mix chemicals together

Always follow the dilution and handling instructions on the product label. The wrong chemical can damage the machine and void the manufacturer warranty. Full guidance is in the operator manual (see Downloads below).

Total Cost of Ownership

Replace the mop bucket. Recover the shift.

Manual mopping caps out around 1,500 sq ft per labour-hour and leaves a slip-risk window. The SS60 covers ~25,300 sq ft per machine-hour and leaves the floor squeegee-dry behind it.

Productivity gain

~17×

vs. manual mop and bucket

Cost per 1,000 sq ft

$1.00

5-year TCO, all-in

Typical payback

3 to 6 mo

for daily-use facilities

Labour displaced

1.0 FTE

single-shift, 50,000 sq ft/yr

Payback Calculator

Calculate your payback.

Hours of cleaning per day 4 Shifts per day 1

Annual labour recovered

$0/yr

Payback period

Assumes manual mop and bucket rate of 140 m²/hr, $28/hr fully-loaded operator cost, 250 operating days/year. Machine rate read from product metafields.

Frequently Asked Questions

Choosing the right machine

Sweeper or scrubber: which one do I need?

Sweepers (like the SL1250 ride-on sweeper) collect dry debris: dust, dirt, leaves, packaging. They use brushes and a dustbin. Scrubbers (like the SS60) apply a cleaning solution through brushes and recover the dirty water through a squeegee, leaving floors visibly clean and dry. Many large facilities run both. If your floors collect dry debris, you need a sweeper. If your floors are sealed and need to look clean and disinfected, and the mop bucket is the bottleneck, you need a scrubber.

Walk-behind or ride-on: does facility size matter?

Yes. As a rule of thumb, walk-behind scrubbers like the SS60 are the right call for facilities cleaning 5,000 to 30,000 sq ft per shift. Above that, the SS75-R ride-on scrubber pays back faster because operator fatigue stops being the bottleneck. Below 5,000 sq ft, a mop and bucket may still be more practical. The SS60 hits the productivity sweet spot for mid-sized warehouses, hospitals, retail, and office buildings.

Operation and maintenance

How long does the SS60 run on a single charge?

3 to 5 hours of continuous scrubbing per full charge, depending on solution flow rate and floor conditions. The lithium-ion battery supports opportunity charging during operator breaks, which extends total shift coverage. Full charge from empty takes 3 to 4 hours.

Can the SS60 be used outdoors or on asphalt?

No. The SS60 is engineered for indoor sealed hard floors only: sealed concrete, epoxy, polished concrete, and ceramic or porcelain tile. It is not suitable for asphalt, gravel, raw or unsealed concrete, or any outdoor surface, and is not designed for floors exposed to rain, snow, or freezing temperatures.

What maintenance does the SS60 need?

After every shift: drain and rinse the recovery (dirty-water) tank, rinse the squeegee, and inspect the brushes. Monthly: clean the solution-tank filter, check the squeegee blades for wear and rotate them, and clean the seals on the recovery tank lid. As needed: replace brushes (typically every 6 to 12 months depending on use) and squeegee blades (consumable). Lithium-ion batteries are maintenance-free for the warranty period: no watering, no equalization, no off-gassing.

What cleaning solution should I use in the SS60?

Use a low-foam, pH-neutral commercial floor detergent, diluted to the ratio on the container, with water up to 60 °C. A neutral cleaner suits daily cleaning on sealed concrete, epoxy, polished concrete and tile; a low-foam alkaline degreaser handles grease in food-service or workshop areas (test a small area first). Never use high-foam or dish soaps, bleach, strong acids, solvents, flammable liquids, or powder detergent — they damage the machine and void the warranty. If foam builds up, add defoamer to the recovery tank, not the solution tank. See the “What to put in the solution tank” section above for the full guide.

Purchase and delivery

How do I request a delivery quote for the SS60?

Use the "Request a Delivery Quote" button on this page or contact us at sales@sumachay.com or 1-844-861-9484. The SS60 ships on a pallet via LTL freight or smaller-format courier depending on facility access. Delivery typically takes 5 to 10 business days after 1 to 3 days of handling. Liftgate delivery and appointment scheduling are available on most routes.

What warranty comes with the SS60?

The SS60 includes a 12-month equipment warranty covering the brush motor, suction motor, controller, control panel, and lithium battery against manufacturing defects under normal operating conditions. Wear items (squeegee blades, scrub brushes, scrub pads, rubber strips, brush plates) are excluded. Warranty registration is automatic at purchase.

Explore More

All floor cleaners Browse the full Sumachay floor-cleaner range Walk-Behind Floor Scrubbers See every walk-behind scrubber Sumachay offers Step up to ride-on: SS75-R For facilities cleaning over 30,000 sq ft per shift Need a sweeper? SL1250 ride-on Dry-debris pickup for warehouses and yards Equipment Hub Browse all equipment