SELR20+ Setup & Support

For SELR20+ trucks with the PIN keypad handle.

Welcome to your Sumachay SELR20+. This guide gets you and your team set up quickly and safely: unpacking, first charge, your PIN, the correct start-up sequence and what the screen codes mean.

Which trucks this guide covers

This guide is for SELR20+ trucks with the PIN keypad handle: number keys 1 to 4, a red × key and a green key above a small display. If your handle has no number keypad, contact us before using this guide.

Read the printed Operator Manual too

This guide supplements, and does not replace, the printed Operator Manual supplied with your truck and required operator training. Only trained, authorised operators may use the truck.

Keep this guide with the truck. When you contact us, have the truck's serial number ready.

Start up in 4 steps

  1. 1
    Power on
    Pull the red emergency power-off button on the chassis up to switch the truck on. Don't twist it.
  2. 2
    Enter your PIN
    Press ×, type your 4-digit PIN, then press .
  3. 3
    Handle down
    Pull the handle down into the driving range (M), between upright and fully down.
  4. 4
    Drive, lift or lower
    Only now use the throttle, lift or lower. Rotate the throttle gently forward or back to move.
Wrong order? The screen shows SRO.

If the throttle, lift or lower is used while the handle is upright or fully down, the truck won't respond and the display shows SRO. This is a normal safety interlock, not a fault. To clear it: switch off (press the red button down), switch on again (pull it up), enter your PIN and press , then pull the handle into the driving range before using any control.

Download the guides

What's in the box & initial inspection

Your SELR20+ arrives with:

  • The SELR20+ truck
  • Its 48 V lithium battery
  • The charger for the battery

Inspect on delivery

  • Check the truck for damage and make sure no parts are missing.
  • Look at the battery. It was inspected before shipping. If it is deformed, hot or has a smell, don't use it and contact us.
  • Slightly flattened wheels after a long time parked are normal. They recover once you drive.
  • The truck arrives fully assembled, with the handle attached. If anything is missing or damaged, contact us before using it.
Never use a damaged truck

Never start a truck that is damaged or faulty. Report damage to us right away, and tag the truck OUT OF ORDER – DO NOT USE until it is fixed.

Know your truck

You control the SELR20+ from the handle (the tiller). The keypad side faces you. The horn, lift and lower buttons are on the side facing the forks.

1 1 2 3 4 5 6 6
Keypad side (faces you)
7 8 9 10
Front side (faces the forks)
  1. 1Turtle buttons Two buttons with the same function: slow speed and upright walking mode.
  2. 2PIN keys 1–4 Enter your PIN at start-up.
  3. 3× Clear Clears digits typed by mistake.
  4. 4 Confirm Press after your PIN.
  5. 5Display Shows the battery charge level and screen codes.
  6. 6Throttle Butterfly controls on both sides. Rotate forward to drive forward, backward to reverse.
  7. 7Belly switch Reversing button at the tip of the handle. If it is bumped while the truck travels toward you, the truck reverses and stops.
  8. 8Horn Sounds a warning.
  9. 9Lift Raises the forks.
  10. 10Lower Lowers the forks.
Red emergency power-off button, on top of the chassis beside the battery.
BMB BrakeDriving rangeBrake
Handle positions: the truck drives, lifts and lowers only in the driving range (M).

The red emergency power-off button is also the truck's power switch. Pressed down, it disconnects the battery and switches off all controls.

The handle has a driving range (M) between two braking zones (B): near upright and fully down. The truck drives, lifts and lowers only with the handle in the driving range.

Key specifications

Capacity 2,000 kg (4,400 lb)
Load centre 600 mm (24 in)
Fork height 75 mm lowered, 190 mm raised
Travel speed 4.5 km/h empty, 4 km/h loaded
Gradeability 10% empty, 5% loaded
Battery 48 V 15 Ah lithium
Brakes Regenerative + electromagnetic
Battery setup & first charge

The lithium battery sits in the bay on top of the chassis, next to the red emergency power-off button.

Lift the battery straight up by its handle.
  • Install the battery, taking care not to damage any wires.
  • The battery is held by an anti-jump stopper. To remove it, loosen the stopper screw, rotate the stopper away, then lift the battery straight up.

First charge

  1. Fully charge the battery before first use.
  2. Follow the charging steps in Charging & battery care. A full charge takes about 3 hours.
  3. Check the charge level on the display.
Handle the battery with care
  • Never strike, drop, pierce or open the battery, or short its terminals.
  • Keep it cool and dry. Never wash it or put it in water.
  • Don't mix batteries of different types, or old and new batteries.
  • If it smells, gets hot, changes colour or deforms, move it to a safe place, stop using it and contact us.
First power-on

Your first power-on is a good time to check that everything works. Clear the area, then:

  1. Switch the truck on by pulling the red emergency power-off button up. Don't twist it: that can break off its cover.
  2. Enter the factory PIN: press ×, type 1 2 3 4, then press .
  3. Check the display shows the battery charge level.
  4. Pull the handle down into the driving range. Test lifting, lowering, steering, the horn and the brake at low speed.
  5. Change the factory PIN to your own (see the next section).
Seeing SRO? That's normal.

If you press the throttle, lift or lower before the handle is in the driving range, the display shows SRO. It's a safety check, not a fault. See Correct start-up sequence.

Your PIN: default & how to change it

The keypad keeps anyone without the PIN from using the truck. The factory PIN is 1234. Change it to your own 4-digit PIN on day one and share it only with trained operators.

Entering your PIN

  1. Press × to clear any stray digits.
  2. Type your 4-digit PIN.
  3. Press to confirm.

Change your PIN

  1. Switch the truck on and enter the PIN 1234, then press .
  2. Press and hold keys 1, 2 and 3 together for 10 seconds. The PIN setting screen opens.
  3. Enter the default PIN 1234 and press .
  4. Enter your new 4-digit PIN and press .
  5. Enter the new PIN again and press . A success screen confirms the change.
Keep your PIN safe
  • Write your new PIN down and keep it somewhere safe.
  • Forgot your PIN? Contact us and we'll help you get back in.
  • Changing your PIN a second time? Contact us first so we can confirm the steps.
Correct start-up sequence

Before every shift

  • Stand in the operating position, put the handle in the driving range, and test lifting, steering, speed, the horn and the brake.
  • Check that the throttle springs back to neutral when you let go. If it doesn't, stop and contact us.
  • Regularly check braking, driving, the horn and the safety systems, and look for hydraulic oil leaks.
Driving, steering, speed modes, lifting & lowering

Driving & steering

  • With the handle in the driving range, rotate the throttle forward to drive forward and backward to reverse. The further you rotate it, the faster you go.
  • Steer with the handle.
  • Top speed is 4.5 km/h empty and 4 km/h with a load.
  • Use the horn to warn people around you.

Braking

  • Let go of the throttle: it returns to neutral, the truck slows electrically, then the electromagnetic brake engages.
  • To slow by reversing, rotate the throttle the other way and release it as the truck starts to move in the new direction.
  • To brake hard, let go of the handle or move it into a braking zone (upright or fully down).

Turtle (slow) mode

Press a turtle button once for slow speed (2.25 km/h). Press it again to return to normal speed (4.5 km/h).

Upright walking mode

For tight spaces such as elevators, hold a turtle button to drive with the handle upright. The buzzer beeps while the mode is on. Release the button to cancel.

Upright mode: move slowly

In upright walking mode the truck moves with the handle in any position. Move slowly, keep the area clear and avoid accidental use of the throttle.

Lifting & lowering

  • Press lift to raise the forks. Lifting stops automatically at the top limit.
  • With the handle in the driving range, press lower. The forks lower under their own weight.
  • If the forks won't lower, keep people away from the load and contact us.

Handling loads

  1. Line up with the pallet and slide the forks in slowly, centred under the load, at the lowest speed.
  2. Lift only enough to move the load.
  3. To unload, set the load down, lower the forks fully and pull out slowly.
Load limits

Never exceed 2,000 kg (4,400 lb). Carry only centred, stable loads. No swinging or overhanging loads.

Emergency stop & safety mechanisms

Red emergency power-off button

  • In an emergency, press the red button down. It disconnects the battery and switches off all controls.
  • With no power, the electromagnetic brake stays on and the truck will not roll.
  • To restart, pull the red button up (don't twist it), then follow the four start-up steps, including your PIN.

Belly switch

If the belly switch at the tip of the handle is bumped while the truck travels toward you, the truck reverses and stops. To reset it, switch the truck off and on again, then enter your PIN.

Brakes

The SELR20+ has regenerative and electromagnetic brakes. If the truck ever moves with the handle upright or fully down, stop using it and contact us.

Operator rules
  • Only trained, authorised operators may use the truck.
  • Never lift or carry people.
  • You may refuse a load that is unsafe or badly stacked.
  • Keep hands and feet away from moving parts.
  • Don't remove or cover warning labels. Keep the nameplate readable.
  • Don't modify the truck.
  • Elevators: get permission, check the elevator can carry the truck, operator and load, enter slowly and centre the truck.
Slopes, ramps & tip-over
  • Maximum slope: 5% with a load, 10% empty.
  • Never turn on a slope, and never drive on a slope with the load facing downhill.
  • Tip-over risks: fast turns, raised, side or oversized loads, swinging loads, ramps or steps, and rough ground.
  • Never park on a ramp.
  • If the truck tips, keep your body clear of the impact point.

Where to use it

  • Use on hard, flat ground. Avoid heavy dust, water, oil or mud, and rain (no more than 10 minutes in light rain).
  • Operate between 0 and 45 °C (32–113 °F). Not for use in cold storage.
  • The truck is not explosion-protected. Keep it out of areas with flammable gas, vapour or dust.
Common mistakes that stop the truck

Most "it won't move" moments are the truck's safety checks doing their job. Here is how to get going again.

If you… What happens Do this
Use the throttle, lift or lower before lowering the handle Nothing moves; screen shows SRO Switch off and on, enter your PIN, pull the handle into the driving range first, then use the controls.
Try to drive with the handle upright or fully down Truck won't move; screen shows ERR34 Move the handle into the driving range.
Press the red emergency button to "reset" a code Everything switches off Pull it up (don't twist it) and follow the four start-up steps in order, including your PIN.
Touch the belly switch while switching on Screen shows ERR16 Let go of the belly switch, then switch off and on. If ERR16 returns, contact us.
Bump the belly switch while the truck moves toward you Truck reverses and stops Switch off and on, then enter your PIN to reset.
Skip × before the PIN, or after it PIN not accepted Press ×, type the PIN again, press .
Run the battery low Speed drops and the charge symbol blinks; at 0% the truck stops Charge the battery.
Overload the forks Forks won't lift Keep the load under 2,000 kg and make sure the battery is charged.
Troubleshooting & screen codes

Codes appear on the display as ERR followed by a number (for example ERR34). Find your code below to see which group it belongs to.

Normal safety interlock: you can fix it
Code What it means What to do
SRO Wrong start-up order: a control was used before the handle was in the driving range Switch off and on and enter your PIN. Pull the handle into the driving range first, then use the controls.
ERR34 Handle is outside the driving range Move the handle into the driving range (M).
Belly switch Truck reversed and stopped after the belly switch was touched Switch off and on, then enter your PIN.
Simple fix: wait or charge
Code What it means What to do
ERR22 · ERR23 · ERR25 Controller or motor too hot (power reduced or stopped) Stop and let the truck cool for 15–25 minutes. If the code returns, contact us.
ERR31 · ERR32 Battery voltage low (power reduced or stopped) Charge the battery. If the code returns on a full charge, contact us.
ERR33 Battery voltage too high Wait 15–35 minutes before using the truck. If the code returns, contact us.
Fault: stop and contact us
Code What it means What to do
ERR16 Belly switch signal at power-on If you touched the belly switch while switching on, let go and switch off and on. If ERR16 returns, contact us.
ERR11 Parameter setting error Stop using the truck and contact us.
ERR12 Overcurrent
ERR14 · ERR15 Current detection error
ERR18 Motor Hall sensor fault
ERR19 Temperature sensor fault
ERR21 Potentiometer fault
ERR26 Motor stall protection
ERR27 Brake fault
ERR29 Motor circuit open
ERR35 Contactor error
ERR38 Display communication error
ERR39 Software version error
When an interlock keeps coming back

If SRO or ERR34 keeps appearing even when you follow the four start-up steps in order, contact us.

Other symptoms

Symptom Do this
No power at all Check the red emergency button is pulled up and the battery is installed. Otherwise contact us.
Forks won't lift Check the load is under 2,000 kg and the battery is charged. Otherwise contact us.
Forks won't lower Keep people away from the load and contact us.
Uneven lifting speed or unusual noise when lifting Stop and contact us.
Throttle doesn't spring back to neutral Stop using the truck and contact us.
Truck moves with the handle upright or fully down Stop using the truck and contact us.
Battery hot, smelly, discoloured or deformed Move it to a safe place, stop using it and contact us.

When you contact us, tell us the code on the display, what you were doing and your truck's serial number.

Charging & battery care

How to charge

  1. Take the truck to your charging area: dry and well ventilated.
  2. Switch the truck off: press down the red emergency power-off button.
  3. Disconnect the battery connector.
  4. Connect the charger and charge following the instructions on the charger. A full charge takes about 3 hours.
Temperature rules
  • Never charge at 0 °C (32 °F) or below.
  • Charge only between 0 and 45 °C (32–113 °F).
  • Battery brought in from the cold? Wait at least 4 hours before charging.
  • Let the battery cool down after use before charging.

Battery care

  • Use only the charger supplied with your truck, and never use it to charge other batteries.
  • Check the charge level on the display. When the charge is low, speed is reduced and the charge symbol blinks: recharge soon.
  • For the charger's indicator lights, follow the label on the charger.
  • Never wash the battery or the truck's battery bay with water.

Storage

For long storage, keep the battery at room temperature and about 30–50% charged. Top it up to 30–50% every 3 months.

Safe shutdown & parking
  1. Park on level ground in a clean area, never on a ramp.
  2. Lower the forks fully.
  3. Press down the red emergency power-off button.
  4. Check the charge level and recharge if needed.

With the power off, the electromagnetic brake holds the truck in place.

If the truck is damaged or not working, tag it OUT OF ORDER – DO NOT USE and contact us.

Warranty & support

Your SELR20+ is a Sumachay Plus model with an 18-month limited warranty.

  • Coverage starts on the purchase date shown on your invoice.
  • The battery is covered against manufacturing defects. Normal, gradual loss of battery capacity over time is not covered.
  • Overloading the truck can void the motor and battery warranty.
  • For a claim, we inspect and diagnose the truck. You arrange shipping to and from our warehouse; repairs are at our discretion, and we ship parts when the fix can be done on site.

Need help?

Sumachay Lifts · 840 Flint Road, Toronto (North York), ON M3J 2J5, Canada

Have your truck's serial number and any screen code ready. We're happy to help.

Need help?

Sumachay Lifts · 840 Flint Road, Toronto (North York), ON M3J 2J5, Canada

Have your truck's serial number and any screen code ready.

v1 · 2026-11-15